These sensors are one way flow sensors meaning that they will only sense water flowing in one direction. Seen to the right is the water flow sensor used in many of the Bestway, Coleman and Lay-Z-Spa branded inflatable hot tub models. If you just installed the hot tub, and it keeps deflating for no clear reason, check if the air valve is leaking by applying soapy water to the valve.The water flow sensor is just as it's name says, it is use to tell a system that water is flowing. According to the manufacturer, a Lay-Z Spa hot tub might deflate for one of two reasons either the air valve is loose, or the spa is torn or punctured.
Coleman Lay Z Spa Manual Ebook That
The first part is the main sensor housing. There are three main components to the sensor. Coleman 455 hot tub manual - heeng coleman 107 hot tub manual pdf - wmcir coleman lazy spa.The operation of the water flow sensor is very simple. If you desire to witty books, lots of novels, tale, jokes, and more fictions collections areNeed Instruction Manual for Coleman Lay Z Spa model 58210. Find a dealer in your area or.Read PDF Coleman 455 Hot Tub Manual Coleman 455 Hot Tub Manual If you ally infatuation such a referred coleman 455 hot tub manual ebook that will offer you worth, get the extremely best seller from us currently from several preferred authors.
The magnet is housed in a small plastic paddle like the one seen to the left. The third part of the sensor, quite obviously, is the magnet. When this piece senses a magnetic field, a small switch inside makes contact completing the circuit in the two wires. This part is the small black tubular piece with the two wires coming off of it like the one seen to the right. The second part is the magnetic reed switch, or proximity switch.
By Laze Up Team.The biggest problem with these sensors is that the magnetic paddles in them fail. Coleman Lay-Z Spa Inflatable Hot Tub Review. If you are looking to enjoy a relaxing spa experience in your inflatable spa with 3 other persons. Because of this, care must be taken to install this sensor in the correct direction for proper operation.Some of the information highlighted below are either never mentioned in the manual or easily overlooked because they just weren’t given enough emphasis on the sales page. This sensor is a one way sensor meaning that it will only sense the flow of water in one direction.
The original sensor paddles have the magnet inset into a hole in the center and then a dab of epoxy glue is put on top. This is why the sensors fail when the magnet gets rusty. Rust reduces the attraction of a magnet. Magnets need iron to attract, and iron rusts when exposed to oxygen and water. Why do magnets rust? Magnets work because they are made of ferrous metals which contain iron.
Never work on your unit with the power plugged in. The first thing is to unplug your pump from the mains socket. The plastic around the magnet will start to crack because of the magnet swelling which allows more water in causing it to snowball into failure.Bestway Original Spare Parts - The official spare parts shop If you are looking for original spare parts or accessories for Bestway products, you will find here all suitable parts for pools, whirlpools, SUPs, pumps and much more.How do you find out if your sensor has failed or is starting to fail.
Now, separate the black connectors on the ribbon cable slightly down from the control panel inside and set the cover to the side. Once those screws are removed, carefully lift the top off being careful of the ribbon cable. Next, remove the cover from your pump/heater unit by removing the six screws in the middle of the unit as indicated in the picture to the right. This is to prevent water flowing out of the flow sensor when you take the cap off.
Inspect the plastic paddle under the cap looking for signs of cracks in the plastic, and signs of rust like the one shown to the right. Carefully lift the top of the sensor off being careful not to loose the round o-ring seal under the cap. Now remove the four screws from the top of the sensor and set them aside. Start by disconnecting the small plug on the two wires attached to the top of the sensor.
On top of that you would have to dismantle the unit even further to be able to remove the old one and install the new one. Some would have you replace the entire water flow sensor assembly which can cost you between $50 and $75 US dollars just for the part. If there is even the slightest bit of wear on the o-ring, it is best to just replace it. While you have the top off, you should also inspect the o-ring for any signs of wear.
It is extremely rare that that part will fail. The sensor that senses the magnetic paddle is the black tube looking part that the wires connect to. If you don't read a shorted condition when the paddle is in the up position, you most likely have a problem with the paddle magnet. Once connected, the water flow sensor should show an open or infinite resistance when the paddle is hanging down and a short or zero ohms when the paddle is in the upward position resting on the cover plate. You will feel a bit of resistance when pushing the wires in, but they should be inserted enough to make a good connection with the connectors inside.
Both the paddle and the kit version come with a replacement nylon pin to attach the paddle as many times these get broken. I sell both the replacement paddles as well as kits that include the paddle and the o-ring seal for the top of the sensor housing. If it does, then your paddle needs to be replaced.
If you decide that you want to go to someon else to purchase the paddle, there are some things that you need to watch out for. These kits can be purchased from our store for $11.49 plus shipping by clicking here. If you also need the o-ring, we sell a kt that contains the paddle, retaining pin and the o-ring. If all you need is the water flow sensor paddle, this can be purchased from our store as a kit that now includes the retaining pin for $10.49 plus shipping by clicking here. Whether you nee just the paddle, or the paddle and o-ring, we have you covered. On the extremely rare chance that the sensor ( black tube) is bad, you may need to contact Bestway or purcase a new water flow sensor, but as mentioned, it is extremely rare that this part goes bad.To repair the flow sensor you should by now know what parts you will need for the repair from the inspection you just did above.
Our kits now include the retaining pin. Put the new paddle in place and push the pin back through the hole. Simply pull the pin out enough to allow you to get the old paddle off. The pin should come out pretty easy. This can easily be removed by pushing on the back side of the pin, the side with the slot in it, with something flat.
Be sure to inspect and clean the channel that the o-ring sits in prior to installing the new one.
0 kommentar(er)
